 |
 |
 |
|
Requires external power supply #PWR-12120USJPS2
Network Readiness for up to Four Serial Devices
NPort® 5450 device servers can conveniently and transparently
connect up to four serial devices to an Ethernet, allowing you to
network your existing serial devices with only basic configuration.
Data transmission between the serial and Ethernet interfaces is
bi-directional. By using NPort® device servers, you not only protect
your current hardware investment, but also allow for future network
expansion. You can both centralize the management of your serial
devices, and distribute management hosts over the network. Independent Operation Mode for each Serial Port
NPort® 5450 device servers can be used to connect different devices
for remote data polling, event handling, or data multicasting over a
TCP/IP network. Each serial port on the NPort® 5450 operates
independently to provide maximum versatility. For example, port 1 can
operate in Driver mode, port 2 in TCP Server mode, and ports 3 and 4 in
TCP Client mode.
User-friendly LCD Panel for Easy Installation
An
LCD panel is built into the NPort® 5400’s top panel, with four buttons
for inputting data, configuration, and selecting the operation mode.
The LCD panel displays the server name, serial number, and IP address,
and can be used to enter or modify parameters such as IP address,
netmask, and gateway.
Redundant DC Power Inputs
NPort®
5400 device servers support redundant power sources and provide both a
DC terminal block input and a DC power jack input. The two power inputs
not only provide power redundancy, but also allow greater flexibility
for use with different applications.
Adjustable Termination and pull High/Low Resistors
Termination
resistors may be needed in some critical environments to prevent the
reflection of serial signals. When using termination resistors, it is
important to set the pull high/low resistors correctly to prevent the
electrical signal from being corrupted. Since no set of resistor values
is universally compatible with all environments, the NPort® 5400 has
four sets of DIP switches on the bottom panel to set the termination
and pull high/low resistor values.
Appearance
Dimensions
Pin Assignments
 Data Sheet
| • Ethernet Interface |
| Number
of Ports |
1 |
| Speed |
10/100 Mbps, auto
MDI/MDIX |
| Connector |
8-pin RJ45 |
| Magnetic
Isolation Protection |
1.5 KV
built-in |
| • Serial Interface |
| Number
of Ports |
4 |
| Serial
Standards |
NPort 5410:
RS-232
NPort 5430/5430I: RS-422/485 (software selectable)
NPort
5450/5450I/5450-T/5450I-T: RS-232/422/485 (software selectable) |
| Connector |
NPort
5410/5450/5450I/5450-T/5450I-T: DB9 male
NPort 5430/5430I: Terminal
block |
| Serial
Line Protection |
15 KV ESD protection
for all signals 2 KV isolation protection (NPort 5430I/5450I/5450I-T) |
| RS-485
Data Direction Control |
ADDC® (automatic data
direction control) |
| Pull
High/Low Resistor for RS-485 |
1 KΩ, 150 KΩ |
| Terminator
for RS-485 |
120 Ω |
| • Serial Communication
Parameters |
| Data
Bits |
5, 6, 7, 8 |
| Stop
Bits |
1, 1.5, 2 |
| Parity |
None, Even, Odd,
Space, Mark |
| Flow
Control |
RTS/CTS and DTR/DSR
(RS-232 only), XON/XOFF |
| Baudrate |
50 bps to 921.6
Kbps |
| • Serial Signals |
| RS-232 |
TxD, RxD, RTS, CTS,
DTR, DSR, DCD, GND |
| RS-422 |
Tx+, Tx-, Rx+, Rx-,
GND |
| RS-485-4w |
Tx+, Tx-, Rx+, Rx-,
GND |
| RS-485-2w |
Data+, Data-,
GND |
| • Software |
| Network
Protocols |
ICMP, IP, TCP, UDP,
DHCP, BOOTP, Telnet, DNS, SNMP V1, HTTP, SMTP, SNTP, Rtelnet, ARP |
| Configuration
Options |
Web Console, Telnet
Console, Windows Utility |
| Windows
Real COM Drivers |
Windows
95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7 x86/x64, Embedded CE 5.0/6.0, XP
Embedded |
| Fixed
TTY Drivers |
SCO Unix, SCO
OpenServer, UnixWare 7, UnixWare 2.1, SVR 4.2, QNX 4.25, QNX 6, Solaris 10,
FreeBSD, AIX 5.x, HP-UX 11i |
| Linux
Real TTY Drivers |
Linux kernel 2.4.x,
2.6.x |
| • Mini Screen with Push
Buttons (standard temp. models only) |
| LCD
Panel |
Liquid Crystal Display
on the case |
| Push
Buttons |
Four push buttons for
convenient on-site configuration |
| • Physical
Characteristics |
| Housing |
Metal, IP30
protection |
| Weight |
740 g |
| Dimensions |
Without mounting kit:
158 x 103 x 33 mm (6.22 x 4.06 x 1.30 in)
With mounting kit: 176 x 103 x 33
mm (6.93 x 4.06 x 1.30 in) |
| • Environmental
Limits |
| Operating
Temperature |
Standard Models: 0 to
55°C (32 to 131°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F) |
| Storage
Temperature |
-40 to 75°C (-40 to
167°F) |
| Ambient
Relative Humidity |
5 to 95%
(non-condensing) |
| • Power Requirements |
| Input
Voltage |
12 to 48 VDC |
| Power
Consumption |
NPort 5410: 350 mA @
12 V, 190 mA @ 24 V
NPort 5430: 320 mA @ 12 V, 175 mA @ 24 V
NPort
5430I: 530 mA @ 12 V, 280 mA @ 24 V
NPort 5450/5450-T: 350 mA @ 12 V, 190 mA
@ 24 V
NPort 5450I/5450I-T: 554 mA @ 12 V, 294 mA @ 24 V |
| • Standards and
Certifications |
| Safety |
UL 60950-1, EN
60950-1 |
| EMC |
CE, FCC |
| EMI |
EN 55022 Class A, FCC
Part 15 Subpart B Class A |
| EMS |
EN 55024 |
| Marine |
DNV (standard temp.
models only) |
| Medical |
EN 60601-1-2 Class B,
EN 55011 |
| • Reliability |
| Alert
Tools |
Built-in buzzer and
RTC (real-time clock) |
| Automatic
Reboot Trigger |
Built-in WDT (watchdog
timer) |
| MTBF
(mean time between failures) |
NPort 5410: 205,153
hrs
NPort 5430: 201,699 hrs
NPort 5430I: 114,540 hrs
NPort
5450/5450I: 206,903 hrs
NPort 5450-T/5450I-T: 206,903 hrs |
| • Warranty |
| Warranty
Period |
5 years |
| Details |
See http://www.moxa.com/support/warranty.htm |
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features
- 10/100M auto-sensing Ethernet
- 4 serial ports, with support for RS-232, RS-422, and RS-485
- Built-in 15 KV ESD surge protection for all serial signals
- Versatile socket operation modes, including TCP Server, TCP Client, UDP, and
Real COM
- Choice of configuration methods: Web console, Telnet console, and Windows
utility
- SNMP MIB-II for network management
- 2 KV isolation protection for NPort 5430I/5450I/5450I-T
- -40 to 75°C operating temperature range (T model)
|
|
|
|
|
|
|
|
|
