Network Readiness for up to Sixteen Serial Devices

NPort® 5610/5630 rackmount device servers can conveniently and transparently connect up to sixteen serial devices to an Ethernet, allowing you to network your existing serial devices with only basic configuration. Data transmission between the serial and Ethernet interfaces is bi-directional. By using NPort® device servers, you not only protect your current hardware investment, but also allow for future network expansion. You can both centralize the management of your serial devices, and distribute management hosts over the network

19-inch Rackmount Device Server

NPort® 5600 device servers come with Tx/Rx LEDs for the serial ports on the front panel, and the 8 or 16 RJ45 serial port connectors on the rear panel. This makes the NPort® 5600 device servers suitable for standard 19-inch rack mounting, allowing you to simplify operation, maintenance, and administrative tasks.

 

Real COM/TTY Ports

Real COM/TTY drivers are provided that make the serial ports on the NPort® 5600 recognizable as Real COM ports by Windows, or Real TTY ports by Linux. In addition to supporting basic data transmission and reception, the NPort® drivers also support the RTS, CTS, DTR, DSR, and DCD control signals.

 

LED Indicators to Ease Your Maintenance Tasks

The System LED, Serial Tx/Rx LEDs, and Ethernet LEDs (located on the RJ45 connector) provide a great tool for basic maintenance tasks and help engineers analyze problems in the field. The NPort® 5600’s LEDs not only indicate current system and network status, but also help field engineers monitor the status of attached serial devices.

 

Adjustable Termination and Pull High/Low Resistors

In some critical environments, termination resistors may be needed to prevent the reflection of serial signals. When using termination resistors, it is also important to set the pull high/low resistors correctly so that the electrical signal is not corrupted. Since no set of resistor values is universally compatible for all environments, the NPort® 5600 has DIP switches on the bottom panel for setting the termination and pull high/low resistor values.

 

Appearance

 

 

Dimensions

 

 

Pin Assignment

Data Sheet

LAN Interface
Number of Ports	1
Speed	10/100 Mbps
Connector(s)	8-pin RJ45
Magnetic Isolation Protection	1.5 KV built-in

• Optical Fiber Interface
Distance	Multi mode: 0 to 2 km, 1310 nm (62.5/125 µm, 500 MHz*km) Single mode: 0 to 40 km, 1310 nm (9/125 µm, 3.5 PS/(nm*km))
Min. TX Output	-20 dBm (Multi mode), -5 dBm (Single mode)
Max. TX Output	-14 dBm (Multi mode), 0 dBm (Single mode)
Sensitivity	-34 to -30 dBm (Multi mode), -36 to -32 dBm (Single mode)

• Serial Interface
Serial Standards	NPort® 5610: RS-232 NPort® 5630: RS-422/485
Number of Ports	8 or 16
Connectors	RJ45 (8 pins)
Serial Line Protection	15 KV ESD protection for all signals
RS-485 Data Direction Control	ADDC® (automatic data direction control)

• Serial Communication Parameters
Data Bits	5, 6, 7, 8
Stop Bits	1, 1.5, 2
Parity	None, Even, Odd, Space, Mark
Flow Control	DSR/DTR and RTS/CTS (RS-232 only), XON/XOFF
Baudrate	50 bps to 921.6 Kbps

• Serial Signals
RS-232	TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422	Tx+, Tx-, Rx+, Rx-, GND
RS-485-4w	Tx+, Tx-, Rx+, Rx-, GND
RS-485-2w	Data+, Data-, GND

• Software
Network Protocols	ICMP, IP, TCP, UDP, DHCP, BOOTP, Telnet, DNS, SNMP, HTTP, SMTP, SNTP, ARP, PPP, SLIP, RTelnet, RFC2217
Driver Support	Windows Real COM driver (for Windows 95, 98, ME, NT, 2000, XP, 2003, Vista, XP x64, 2003 x64, Vista x64), Linux Real TTY driver, Fixed TTY driver (for SCO Unix, SCO OpenServer, UnixWare 7, UnixWare 2.1, SVR 4.2, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i)
Configuration Options	Web Console, Telnet Console, Windows Utility

• Mini Screen with Push Buttons
LCD Panel	Liquid Crystal Display on the case
Push Buttons	Four push buttons for convenient on-site configuration

• Physical Characteristics
Enclosure	SECC sheet metal (1 mm), providing IP30 protection
Weight	NPort® 5610-8: 3340 g NPort® 5610-8-48V: 3160 g NPort® 5630-8: 3380 g NPort® 5610-16: 3420 g NPort® 5610-16-48V: 3260 g NPort® 5630-16: 3400 g
Dimensions	Without ears: 440 x 45 x 198 mm (17.32 x 1.77 x 7.80 in) With ears: 480 x 45 x 198 mm (18.90 x 1.77 x 7.80 in)

• Environmental Limits
Operating Temperature	0 to 55°C (32 to 131°F)
Operating Humidity	5 to 95% RH
Storage Temperature	-20 to 75°C (-4 to 167°F)

• Power Requirements
Input Voltage	NPort® 5610/5630: 100 to 240 VAC, 47 to 63 hz NPort® 5610-48V: ±48 VDC (20 to 72 VDC, -20 to -72 VDC)
Power Consumption	NPort® 5610-8/16: 141 mA @ 100 VAC, 93 mA @ 240 VAC NPort® 5630-8/16: 152 mA @ 100 VAC, 98 mA @ 240 VAC NPort® 5610-8/16-48V: 135 mA @ 48 VDC
Power Line Protection	4 KV burst (EN61000-4-4: EFT/B), 2 KV surge (EN61000-4-5)

• Regulatory Approvals
Safety	UL (UL60950-1), TÜV (EN60950-1)
EMC	CE (EN55022 Class A, EN55024), FCC Part 15 Subpart B Class A NPort® 5610 only: IEC61000-4-12
Medical	EN60601-1-2 Class B, EN55011

• Reliability
Alert Tools	Built-in buzzer and RTC (real-time clock)
Automatic Reboot Trigger	Built-in WDT (watchdog timer)
MTBF (meantime between failures)	NPort® 5610-8: 97294 hrs NPort® 5610-16: 94928 hrs NPort® 5610-8-48V: 96758 NPort® 5610-16-48V: 94417 hrs NPort® 5630-8: 118405 hrs NPort® 5630-16: 91483 hrs

• Warranty
Warranty Period	5 years
Details	See www.moxa.com/warranty