Home > Perle > Perle Industrial Media Converters > Perle Stand-Alone Media Converters > Perle Managed Media Converters > Perle Managed Ethernet to Fiber > Perle Managed 10/100BT Rate Converting to Fiber >

05071034
05071034
See any errors on this page?
Please let us know.
  
Perle SMI-110-S2ST120 - Fast Ethernet IP Managed Standalone Media and Rate Converter 100BTX RJ45 [100m/328ft] to 100BZX 1550nm single mode ST [120km/74.6 miles]
List Price: $3,416.00
Our Price: $2,664.00
Contact Us for Partner Pricing. (more info)



Availability:: Usually Ships in 24 Hours; However, Due To Shortages Contact Sales to Verify
Product Code: 05071034

Description Technical Specs Drivers & Downloads
 

Perle’s advanced line ofManaged 10/100 Ethernet Media Converters, transparently connect UTP ethernet copper to multimode or single mode fiber.  While providing an economical means of extending your existing copper based network connection, these media converters are SNMP manageable to enable complete control and status viewing of your fiber links.

Perle 10/100 Managed Media Converters come standard with extensive cost and time saving features.  In addition,  a lifetime warranty and free worldwide technical support make Perle's Managed 10/100 Ethernet Converters the smart choice for IT professionals. 
 
 
Features

SMI-110 Managed Fast Ethernet Media Converter Features

QOS ( Quality of Service )
  • Bandwidth Allocation via rate limiting
  • IEEE 802.1P tagged frame priority control
  • IEEE 802.1P priority tag remapping
  • IP TOS ( Type of Service ) priority for IPV4 Diffserv or IPV6 traffic class frames
  • Congestion Service Policy through WQF ( Weighted Fair Queuing ) or Strict Priority Queuing ( default )
VLAN Tagging
  • Default – Transparent to VLAN frames
  • Enable discarding of tagged frames
  • Enable discarding of untagged frames
  • Untag – Removes any existing tag
  • Insert Tag – Insert (if original frame is untagged) or replace (if original frame is tagged) the VLAN ID and priority with the configured default VLAN ID and priority tag.
  • Insert Double tag (Q in Q) – Append an additional tag using the configured default VLAN ID and priority.
Unknown Multicast Frame filtering When enabled, Multicast frames with an unknown destination address are not allowed to egress the port
Unknown Unicast Frame filtering When enabled, Unicast frames with an unknown destination address are not allowed to egress the port
Unidirectional Ethernet When enabled, provides the ability to restrict port to one-way traffic flow. Used in applications such as unidirectional video broadcasting as well as providing security for ethernet connections in accessible public areas
Configuration Mode selection Select whether to use the on-board DIP switches or the management software for mode selection
Auto-MDIX Can manually set Auto or MDIX on the copper port via on-board strap or via the management software.
Auto-MDIX (automatic medium-dependant interface crossover) detects the signaling on the UTP interface to determine the type of cable connected (straight-through or crossover) and automatically configures the connection when enabled. With Auto-MDIX enabled, either a straight-through or crossover type cable can be used to connect the media converter to the device on the other end of the cable.
Converter Information
  • User configurable media converter name
  • User configurable fiber port name
  • User configurable copper port name
  • Hardware revision number
  • Firmware version number
DIP switch settings View hardware DIP switch settings
Selectable Max Packet Size Set max packet size to 1522, 1518 or 2048 ( default )
10BaseT Extended Distance Normal/extended – default Normal. By configuring as “extended”, the 10baseT receiver sensitivity is increased providing the possibility of a 10BaseT connection greater than 100m.
Port Control Enable or disable individual fiber or copper port on the converter
Copper Port Status
  • Port Enabled (Yes/No)
  • Link Status (Up/Down)
  • Auto Negotiation Settings (Disabled, Complete or In Progress)
  • Resolved as crossover MDI or MDIX type
Fiber Port Status
  • Port Enabled (Yes/No)
  • Connector type (SC, LC, ST)
  • Link Status (Up/Down)
  • Far End Fault (OK, Failed)
  • Fiber Loopback mode (On/Off)
Control
  • Reset
  • Reset to factory default
  • Reset Statistical counters
  • Phy specific commands such write/read config, read dip switches
  • Update firmware
  • Fiber Loopback mode. (On/Off)
  • Upload/download configuration
Detailed port statistics To assist in troubleshooting copper and fiber links, an extensive list of ingress and egress counters for both copper and fiber ports are available. These statistics can be viewed locally via the management module or from a central SNMP NMS on the network
Auto-Negotiation (802.3u) The media converter supports auto negotiation on the 10/100Base-TX interface.
Link Pass-Through With Link Pass-Through the state of the UTP receiver is passed to the fiber transmitter to make the media converter appear transparent to the end devices that are connected. In addition if Far-End Fault is enabled the media converter can turn off the 10/100Base-TX transmitter when a FAR-End Fault is received.

Using Link Pass-Through with Far-End Fault minimizes data loss when a fault occurs. Should a fault occur, the end devices have the indication of a failure available to them making trouble shooting easier.
Far-End Fault (FEF) The media converter implements the 802.3 standard for Far-End Fault for the indication and detection of remote fault conditions on the 100Base-X fiber connection. With Far-End Fault enabled the media converter transmits the Far-End Fault Indication over the 100Base-X fiber connection whenever a receive failure is detected on the 100Base-X fiber connection. The media converter continuously monitors the100Base-X fiber connection for a valid signal.

The action the media converter takes on receiving a Far-End Fault Indication is dependent on the Link Pass-Through switch setting.
Pause (IEEE 802.3xy) Pause signaling is an IEEE feature that temporarily suspends data transmission between two devices in the event that one of the devices becomes overwhelmed. The media converter supports pause negotiation on the 10/100Base-TX copper connection.
Remote Loopback The media converter is capable of performing a lookback on the fiber port.

SMI-110 Advanced Management Features

Enterprise and carrier-grade security is available through the support of strong authentication systems such as TACACS+, RADIUS and LDAP. Secure in-band access is assured via SNMPv3, SSH CLI and secure HTTPS Internet browser.

SNMP
  • Full read/write capabilities via central SNMP servers and PerleVIEW
  • Send SNMP traps ( up to 4 servers )
  • SNMPv3, V2C and V1
  • SNMPv3 – encryption and authentication for both management and trap support
  • RFC1213 MIB II
  • Proprietary MIB provided
Telnet / SSH CLI access In-band command line access via Telnet or SSH application
Internet Browser access
Console port CLI access Out-of-band command line access via Cisco compatible RJ45 serial console port using common “rolled” CAT5 cable.
Console port can be enabled ( default ) or disabled
Concurrent management sessions Run multiple management sessions simultaneously for multiple users
Inactivity timeout Protect secure management sessions by setting an inactivity timeout value
Alert event reporting Alert level events are stored in the local event log and sent as:
  • SNMP traps to up to 4 servers
  • SYSLOG messages to a SYSLOG server
  • Email to user defined email address
Advanced IP feature set
  • IPV4 and IPV6 address support
  • DHCP
  • DNS
  • Dynamic DNS
  • NTP
  • TFTP
  • Telnet
  • SSH V2 and V1
  • HTTP
  • HTTPS
Advanced Management User Authentication with primary and secondary server support
  • TACACS+
  • RADIUS
  • LDAP
  • Active Directory via LDAP
  • RSA Secure ID-agent or via RADIUS authentification
  • Kerberos
  • NIS
Advanced Management User Authorization and Accounting
  • TACACS+
  • RADIUS
Encryption
  • AES (256/192/128), 3DES, DES, Blowfish, CAST128, ARCFOUR(RC4), ARCTWO(RC2)
  • Hashing Algorithms: MD5, SHA-1, RIPEMD160, SHA1-96, and MD5-96
  • Key exchange: RSA, EDH-RSA, EDH-DSS, ADH
  • X.509 Certificate verification: RSA, DSA
Access Control List An access control list can be created which can filter out only those workstations that are authorized to access the management resources. Filter on IP and/or Ethernet MAC addresses
Network Services Filter Enable only those network services on the management module that are allowed on your network ( Telnet, SSH, HTTP, HTTPS, SNMP )
Firmware download Update the latest level firmware for management and media converter modules via TFTP or PerleVIEW


Browse for more products in the same category as this item:

Perle > Perle Industrial Media Converters > Perle Stand-Alone Media Converters > Perle Managed Media Converters > Perle Managed Ethernet to Fiber > Perle Managed 10/100BT Rate Converting to Fiber