About This Item
Overview
Details
When you need to extend Ethernet services beyond the general IEEE 802.3 limits of 328ft / 100m in extreme temperatures, and new fiber cabling is cost prohibitive, Ethernet Extenders are the perfect solution. Perle Ethernet Extenders transparently extend up to four 10/100/1000 Ethernet connections across copper wiring. Use single twisted pair ( CAT5/6/7 ) or any existing copper wiring previously used in alarm circuits, E1/T1 circuits, RS-232, RS-422, RS-485, CCTV and CATV applications.
Equipment found in traffic management, oil and gas pipelines, weather tracking, industrial and outdoor applications must function in temperatures that cannot be supported by a commercial based Ethernet Extender. With the ability to operate in industrial grade temperatures of -40F to +167F (-40C to +75C) along with a rugged steel casing, these simple and effective point to point Ethernet Copper Extenders are ideal to extend the distance between two industrial Ethernet devices subjected to harsh environments and severe temperatures such as security cameras, wireless access points, alarms, traffic controllers, sensors and tracking devices.
Perleís advanced features such as Link
Pass-Through*, Interlink Fault Feedback*, and Loopback allow Network
administrators to ìsee everythingî for more efficient troubleshooting
and less on-site maintenance. These cost and time saving features, along
with a lifetime warranty and free worldwide technical support, make Perle Ethernet Extenders the smart choice for IT professionals. eX-S1110 Ethernet Extenders are also available with support for Commercial Temperature ranges and high density applications.
- Extends 10/100/1000Base-T Ethernet up to 10,000 feet ( 3 KM ) over 2-wire 24 AWG twisted pair
- Rugged-designed for harsh industrial -40 to 75C temperatures ( -40 to 167F )
- Hi-Speed – up to 200+ mbps aggregate bandwidth
- Transparent operation for all Ethernet protocols including 802.1Q VLAN packets and IP video compression schemes
- One or four 10/100/1000 Ethernet ports
- Advanced features: Link Pass-Through*, Interlink Fault Feedback*, Auto-MDIX and Loopback
Documentation
Features
| Extend Ethernet over twisted pair | Extend an Ethernet link over category 5e, 6 and 7 cabling up to 10,000 feet ( 3 km ) |
| Extend Ethernet over Coaxial cable | Extend an Ethernet link over 75 ohm coaxial cable |
| Hi-Speed Performance | Utilizes second generation VDSL2
technology ( ITU-T Recommendation G.993. ) . When operating under
ìProfile 30aî, Perle Ethernet extenders can provide an aggregate data
rate capability of over 200 mbps. Actual distance and performance may vary depending on the type / gauge and condition of the wire used. |
| Plug and Play operation | Perle Ethernet Extenders will
automatically configure your VDSL interlink connection. The CO/CPE peer
association will be determined automatically by the Ethernet Extender.
No need to set CO / CPE VDSL pairing. Once a connection is made, both ends will automatically adjust relevant VDSL parameters to optimize the level of bandwidth possible across the copper link. |
| Link Pass-Through* | With Link Pass-Through the state of
the 10/100/1000Base-T Ethernet connection is ìpassed throughî the VDSL
link to the 10/100/1000Base-T Ethernet connection on its remote peer. A
managed switch on the remote end can then report the state (link up or
link down) to its network management system so that any errors can be
detected and recovered early. Competitive Ethernet extenders without this feature will never detect or report any error conditions. |
| Interlink Fault Feedback* | Similar to the Link Pass-Through feature, a loss of VDSL link will drop the 10/100/1000 Ethernet ports on each end until the link recovers. |
| Auto-Negotiation | The Ethernet Extender supports auto negotiation on the 10/100/1000Base-T interface. |
| Auto-MDIX | Auto-MDIX (Automatic Medium-Dependent Interface crossover) detects the signaling on the 10/100/1000 Ethernet RJ45 interface and determines the type of cable connected (straight-through or crossover) and automatically adopts a compatible pinout. |
| Fixed Speed and Duplex | Some Ethernet equipment require a fixed speed and duplex be used or cannot auto-negotiate. By disabling Auto-Negotiation on the Ethernet Extender, a fixed speed of 10, 100 or 1000 mbps as well as Full or half Duplex can be configured through DIP switches. |
| VLAN | Transparent to tagged VLAN ( 802.1Q ) packets. |
| Transparent to IP Video compression protocols | Fully transparent to such IP video compression schemes such as MPEG-4, H.264 and MJPEG. |
| Power Strain Relief strap | A strain relief strap is provided to ensure a solid and secure power connection to the Ethernet Extender. Ideal for areas that may be exposed to vibration. |
| Loopback | When enabled, will perform a loopback on the copper VDSL Interlink. |
*Available on 1 port models.