About This Item
Overview
Details
Perle eXP-S1110PE PoE+ Gigabit Ethernet Extenders transparently extend Ethernet beyond the general IEEE 802.3at limits of 328ft / 100m while providing Power over Ethernet ( PoE+ ) to standards-based compliant devices such as IP cameras, VoIP phones and wireless access points.
This technology enables users to transparently extend up to four 10/100/1000 Power over Ethernet connections across copper wiring. Use single twisted pair ( CAT5/6/7 ), coax or any existing copper wiring previously used in alarm circuits, E1/T1 circuits, RS-232, RS-422, RS-485, CCTV and CATV applications.
These PoE+ Ethernet Extenders are classified as Power Sourcing Equipment (PSE). While using standard UTP cables that carry Ethernet data, Perle eXP-S1110PE PoE Ethernet Extenders provide up to 30 watts of power to Powered Devices (PDs). Learn more about PoE.
These simple and effective point to point Ethernet Copper Extenders are perfect for commercial buildings, residential units, hospitality environments, and connecting a remote office or private-network backbone to a corporate LAN Ö anywhere you need 10/100/1000 Ethernet communication links for PoE+ devices up to 10,000ft (3KM) in distance.
Perleís advanced features such as Link Pass-Through* and Interlink Fault Feedback*, Loopback and remote PD reset*, enable Network administrators to ìsee everythingî for more efficient troubleshooting and less on-site maintenance. These cost and time saving features, along with a lifetime warranty and free worldwide technical support, make Perle Ethernet Extenders the smart choice for IT professionals. eXP-S1110PE PoE+ Gigabit Ethernet Extenders are also available with support for PoE.
eXP-S1110PE PoE+ Gigabit Ethernet Extender Features
| Extend Ethernet over twisted pair | Extend an Ethernet link over category 5e, 6 and 7 cabling up to 10,000 feet ( 3 km ) |
| Extend Ethernet over Coaxial cable | Extend an Ethernet link over 75 ohm coaxial cable |
| On-board PoE Power Controller | As a fully compliant IEEE 802.3af
and 802.3at PSE end-span device, this Ethernet Extenderís PoE power
controller provides compliant power provisioning and monitoring,
properly sensing through signature detection whether or not the attach
Ethernet devices are PoE capable or not. This provides a safe connection
for both PoE and Non-PoE capable devices. Competitive PoE Ethernet Extender products operate as a simple passive power injector and will always apply power to RJ45 port pins which may result in damage if non-PoE compliant Ethernet devices are accidently attached. Click here for more details |
| Advanced Power capabilities |
|
| Fully compliant 802.3af PoE and 802.3at POE+ PSE |
|
| PSE Status Indicator | A multi-color LED provided presents the status of the PSE function for easy troubleshooting of power over Ethernet connections |
| PD Power Reset ( Port 1 ) | Ideal for remotely resetting
equipment, this configurable function performs a momentary power reset
to the attached Powered Device (PD) on Port #1. Read our PD Reset Tech Note for further details on this feature |
| Broadest range of PoE devices supported | Support is included for a broad range of PD ( Powered Devices )
|
| Hi-Speed Performance | Utilizes second generation VDSL2
technology ( ITU-T Recommendation G.993. ). When operating under
ìProfile 30aî, Perle Ethernet Extenders can provide an aggregate VDSL
line rate capability of up to 200 mbps. Actual distance and performance may vary depending on the type / gauge and condition of the wire used and if required, the amount of power you require across the VDSL Link |
| Plug and Play operation | Perle Ethernet Extenders will
automatically configure your VDSL interlink connection. The CO/CPE peer
association will be determined automatically by the Ethernet Extender.
No need to set CO / CPE VDSL pairing. Once a connection is made, both ends will automatically adjust relevant VDSL parameters to optimize the level of bandwidth possible across the copper link. |
| Link Pass-Through* | With Link Pass-Through the state of
the 10/100/1000Base-T Ethernet connection is ìpassed throughî the VDSL
link to the 10/100/1000Base-T Ethernet connection on its remote peer. A
managed switch on the remote end can then report the state (link up or
link down) to its network management system so that any errors can be
detected and recovered early. Competitive Ethernet extenders without this feature will never detect or report any error conditions. |
| Interlink Fault Feedback* | Similar to the Link Pass-Through feature, a loss of VDSL link will drop the 10/100/1000 Ethernet port on each end until the link recovers. |
| Auto-Negotiation | The Ethernet Extender supports auto negotiation on the 10/100/1000Base-T interface. |
| Auto-MDIX | Auto-MDIX (Automatic Medium-Dependent Interface crossover) detects the signaling on the 10/100/1000 Ethernet RJ45 interface and determines the type of cable connected (straight-through or crossover) and automatically adopts a compatible pinout. |
| Fixed Speed and Duplex | Some Ethernet equipment require a fixed speed and duplex be used or cannot auto-negotiate. By disabling Auto-Negotiation on the Ethernet Extender, a fixed speed of 10 or 100 mbps as well as Full or half Duplex can be configured through DIP switches. |
| VLAN | Transparent to tagged VLAN ( 802.1Q ) packets. |
| Transparent to IP Video compression protocols | Fully transparent to such IP video compression schemes such as MPEG-4, H.264 and MJPEG. |
| Power Strain Relief strap | A strain relief strap is provided to ensure a solid and secure power connection to the Ethernet Extender. Ideal for areas that may be exposed to vibration. |
| Loopback | When enabled, will perform a loopback on the copper VDSL Interlink. |
*Available on 1 port models.
Features
- Extends 10/100/1000Base-T Ethernet up to 10,000 feet ( 3 KM ) over 2-wire 24 AWG twisted pair or Coaxial cable
- Power remote PoE+ devices across 2-wire twisted pair or coaxial cable
- On-board PoE+ power controller for true compatibility with IEEE 802.3at standard
- Hi-Speed – up to 200 mbps aggregate line rate
- Transparent operation for all Ethernet protocols including 802.1Q VLAN packets and IP video compression schemes.
- Advanced features: Link Pass-Through*, Interlink Fault Feedback*, Auto-MDIX
and Loopback, remote PD power reset*, Plug and Play - Auto configuration of VDSL